| G-Switch 东莞品赞电子科技有限公司www.dg-switch.com |
SPECIFICATION
規格書 |
| Designation 品名: | Φ2.5 PHONE JACK |
| Model No. 型 號: | PJ-212 |
| 1. Rating額定值: | DC 30V 0.5A |
| 2. Operation temperature range 使用溫度範圍: | -20℃~+70℃ |
| 3. Preservative temperature range 保存溫度範圍: |
|
4. Construction dimension
結構尺寸: | Apply to the appended drawing:
符合附加圖紙 |
| Item 项目 | Test condition 測試條件 | Specification規格 |
| 5. Electrical characteristics電氣性能 |
| 5A | Contact Resistance
接觸阻抗 | Being measured at 1KHz small current
contact esistance meter.
在1KHZ小電流下測量. | 30mΩ max.
30毫歐以下. |
| 5B | Insulation Resistance
絕緣阻抗 | Measurements shall be made following
application of DC
250V potential across terminals and across
terminals and frame for 1 minute.
在端子之間和端子與殼之間加DC 250V條件下,
持續1分鐘測量. | 100MΩ min.
100兆歐以上. |
| 5C | Withstand Voltage
耐電壓 | AC 500V (50Hz or 60Hz) shall be applied
across terminals and across terminals
and frame for one minute.
在端子之間和端子與殼之間加AC 500V
(50HZ或60HZ)條件下,持續1分鐘測量. | There shall be no breakdown.
無擊穿現象出現. |
| 6. Mechanical characteristics 機械性能 |
| 6A | Insertion and
Extraction force
插拔力 | Being measure at across spring piece
and across matching plug for ergometer.
用測力計在插頭與彈片之間進行測量. | Insertion and extraction force: 3~25N
插拔力: 3~25N |
| 6B | Terminal Strength
端子強度 | A static force of 5N being applied in
one direction on the tip of terminal
for 10sec.
将5N之靜負荷施加於端子頂部的一個
方向持續10秒。 | (1). Contact resistance: 30mΩmax.
接觸阻抗:30毫歐以下.
(2). Insertion and withdraw force: 3~25N
插入力和拔出力：3~25N
(3). Electrical characteristics and
mechanical characteristics shall
be satisfied.
Without distinct damage.
机械，电气性能满足规定要求，无异常发生 |
| 7. Durability 耐久性 |
| 7A | Soldering test
可焊性試驗 | The tip of the terminals shall be dipped
2mm in the solder bath at a temperature
of 240±5℃ for 3±0.5sec.
端子頂部被浸入焊錫池2mm深,溫度
240±5℃,時間3±0.5秒。 | A new uniform coating of solder
shall cover a minimum of 95%
of the surface being immersed.
浸入的部分95%以上表面將被錫覆蓋. |
| 7B | Resistance to
soldering heat
耐焊接熱 | The jack shall be put into at the temperature
of 250±5℃ in 5±1sec(Automatic soldering)
or 380±5℃ in 3±1sec(Manual soldering)
after which measurement shall be made.
将产品端子浸入锡炉, 250±5℃，5±1秒
(自动焊);
380±5℃，3±1秒(手工焊) | (1). Contact resistance:30mΩmax.
接觸阻抗:30毫歐以下.
(2). Insertion and withdraw force: 3~25N
插入力和拔出力：3~25N
(3). Electrical characteristics and
mechanical characteristics shall
be satisfied.
Without distinct damage.
机械，电气性能满足规定要求，
无异常发生 |
Remark
備 註 | G-Switch 东莞品赞电子科技有限公司 www.dg-switch.com |
| Designation 品名: | Φ2.5 PHONE JACK |
| Model No. 型 號: | PJ-212 |
| Item 项目 | Test condition 測試條件 | Specification規格 |
| 7C | Life test
壽命試驗 | 5,000 cycles of operation at a rate of 20~30
cycles per minute with unloading.
無負載條件下,每分鐘20~30次的速度操作5,000次。 | (1). Contact resistance:30mΩmax.
接觸阻抗:30毫歐以下.
(2). Insertion and withdraw force: 3~25N
插入力和拔出力：3~25N
(3). Electrical characteristics and
mechanical characteristics shall be satisfied.
Without distinct damage.
机械，电气性能满足规定要求，无异常发生 |
| 7D | Heat test
耐熱試驗 | At 85±2℃ for 96 hours, after test keep in
normal condition for 30 minutes.
在85±2℃環境中放96小時,再放在
正常環境中30分鐘後進行測試. | (1). Contact resistance: 30mΩmax.
接觸電阻:30毫歐以下
(2). Insulation resistance: 100MΩmin.
絕緣電阻: 100兆歐以上
(3). There shall be no sign of damage
mechanically and electrically.
無任何迹象顯示機械及電器性能之損壞. |
| 7E | Humidity test.
耐濕試驗 | The condition of temperature 40±2℃
and humidity 90 95% for 96 hours,
after test keep in normal condition
for 30 minutes.
在溫度40±2℃,濕度90-95%環境中放96小時,
再放在正常環境中30分鐘後進行測試. |
| 7F | Cold test
耐寒試驗 | At –40±2℃ for 96 hours, after test keep
in normal condition for 30 minutes.
在-40±2℃環境中放96小時,再置於
正常環境中30分鐘後進行測試. |
| 7G | Salt spray test
噴霧試驗 | At 5% Nacl liquor for 24 hours, after washing,
keep in normal condition for 30 minutes.
5%的Nacl溶液中噴霧24小時,用水清洗並在
室溫下放置30分鐘. | Without excessive Corrosion or crack
in appearance
表面無明顯腐蝕或鍍層脫落現象 |
| 8. Standard condition 試驗、測定狀態 |
Unless otherwise specified, the test and measurements shall be carried out as follows:
Ambient temperature 溫度: 5℃~35℃
Relative humidity 相對濕度: 45~85%
Air pressure 氣壓：86~106kPa(860~1060mbar)
However if doubt arises on the decision based on the measured values
under the above-mentioned conditions,
the following condition
shall be employed:但在對判定産生疑義時，按下述狀態實施:
Ambient temperature 溫度: 20±2℃
Relative humidity 相對濕度: 65±5%
Air pressure 氣壓：86~106kPa(860~1060mbar)
|
Remark
備 註 | G-Switch 东莞品赞电子科技有限公司 www.dg-switch.com
|