【专业生产】电子调节仪 XMZ-101系列数显式温度调节器 高品质
采用先进的中、大规模集成电路，应用独特非线性校正技术，设定形式有旋钮设定和数字拨码开关设定。 与传统观动圈仪表、电子调节器相比，具有现实精度高、控温性能好、抗震动性强、可靠性佳、读书清晰、无视差，可远距离观察；体积轻巧，安装方便等优点。在调节形式上有二位式、三位式、时间比例式，可硅控连续调节式、PID调节式等多种，并可根据用户需要增加超限报警输出功能。 显示误差：<=±0.5%±1字或<=1%±1字二档； 设定点误差：<=±1%±1字； 控制点误差：<=0.5%； 冷端补偿：0-40℃内误差小于2℃； 时间比例调节：比例带3-6%，周期30±10S； 超限报警：报警输出i但在被测信号超过设定值的2-10%（全量程），消警范围<=1%； 输出脉冲信号：幅值大于3V，幅度大于40uS的移相脉冲或过零触发脉冲； 输出触点容量：交流220V，3A（阻性负载）或1A（感性）； 温度系数：在0-50℃范围内偏离20±2℃适用时，其温度系数小于0.05%℃； 工作电源：交流220V±10%，50Hz，功耗小于5W； XMT series digital diaplay meter adopts advanded medium and large-scale inteliigent circuit with unique nonlinear revise technology,there are two setting type the rotatin setting and the push digital setting.XMTA,XMTD,XMTE series acordance with international DIN standard. Compared with traditional moving coil meter and electric adjuster,it has high accuracy of diaplay,good perfomance of temperature control,good shock resistance,good reliability,clear reading,no parallax.far diatance observation available,small volume,simple installation.There are many kinds of adjust type two digits,three digits,time proportion type.SCR continous adjusting type,PID adjusting and so on,and it can also add over ran alarm output function,according to user reuire,the product is a replacing product for XC series,TD series temperature controller,widely used for temperature check and control in range of -200-1600℃ on plastic machine,package machine,food machine,textile machine and metallurgy、refigeration、chemical industry、medical treatment etc.When it is equipped with sensor,it can also be used for diaplay and adjusting od physical likes pressure,flux,liquid level etc. 1.Display mode:XMTA series,3½digital tube diaplay the checked value 2.Dislay deviation:≤±0.5% ± 1character or ≤± 1% ± 1character two levels 3.Set point deviation:≤± 1% ± 1% ± 1charaters 4.Control point switching deviation:≤0.5% 5.Cold junction compensation:deviation less than 2℃ with 0-10℃ 6.Time proportion adjusting:proportional band 3-6%,cycle 30 ± 10S 7.Overran alarm:Alarm output point is within 2-10%(full scale) that the checked signal exceed the set value,alarm delete range≤1% 8.Output contact capacity:AC 220V,3A(resistant load) or 1A(perpetual) 9.P,I,D adjustment:(1)output 0-10mA; (2)load 800 ± 800Ωa; (3)P(proportion band)4%; (4)I(integral time)2.5min; (5)D(differential coefficient time)30S 10.Output impulse signal:ampliture value more than 3V,more than 40uS phase-shifting impulse or zero trigger impulse 11.Temperature factor:less than 0.05%℃ in condition of 20±2℃ departure from the range of 0-50℃ 12.Working power supply:AC 220V ± 10%,50Hz,power comsumption less than 5W 13.Working environment:temperature 0-50℃,relative humidity 30-85% no corrosive gas 14.Weight:about 0.8kg 
|